1/8" Two-Piece Launch Rod

Ideal replacement rod and alignment tool. This 1/8 inch (3.2 mm) diameter launch rod is ideal for most standard engine powered rockets. It attaches to the launch pad then you can align the launch lugs on your Estes rocket to the launch rod and slide it down. As the rocket launches, it quickly gains enough speed to fly with stability, thanks to the launch rod, and then flies into the air. Fits the 2215 Porta-Pad II Also works great when used as an alignment tool on model rockets that req…

24" Estes Nylon Parachute

Strong and durable to safely recover larger-sized rockets Bright red for great visibility Comes preassembled A fully assembled 24 in. (61 cm) nylon parachute is intended for larger-sized model rockets where the strength of the recovery system is paramount. Made of high-quality red nylon cloth, this chute features stitched braided nylon shrouds for reliable rocket recovery and lasts longer than an entry-level plastic shoot.

24mm to 29mm Motor Adapter Set (2 pk)

Very simple transformation of an Estes 24 mm casing into an Estes 29 mm casing size. Reusable. Adapts Estes 24 mm C11/D, Estes 24 mm E and Estes E30 series Composite engines to a 29 mm Estes casing size. Also adapts other brands of 24 mm composite single use and RMS motor systems. 2 sets per package. Includes orange paper adapter tubes, as shown, and are designed for reuse over and over.

3/16" Two-Piece Maxi Rod

Launch rod with extra strength and length for larger rockets. Going big? You might need a stronger launch rod, like this 3/16 diameter rod built for heavier rockets and higher power motors. It attaches to the launch pad, and your Estes rocket simply slides over the rod using the launch lugs attached to the rocket. As the rocket launches, it quickly gains enough speed to fly with stability, and then leaves the launch rod. That requires roughly 30mph, and this length is perfect to accelerate…

30" Estes Nylon Parachute

Strong and durable to safely recover larger-sized rockets Bright red for great visibility Comes preassembled A fully assembled 30 in. (76 cm) nylon parachute intended for larger model rockets where strength of the recovery system is paramount. Made of high-quality red nylon cloth, this chute also features stitched braided nylon shrouds for reliable rocket recovery.

AltiTrak Altitude Tracker

How high did it really go? Next time, measure it with this easy to use device. Pull the trigger, follow the rocket in the sights to apogee, then release the trigger to lock the reading. It is that easy. No need for hundreds of dollars of altimeters! The Estes Altitrack was designed for educational uses, but is perfect for any application of rapid design. Track the altitude of your rocket without reducing the height by adding mass. Two AltiTraks can give you much greater accuracy. Perfect f…

C11, D & E Engine Model Rocket Display

Model Rocket Display stand for all of your C11, D & E engine size model rockets! 3 to a pack. What a great value! Display your rockets in style! Available in mini, standard and C11, D & E engine mount sizes.

E Launch Controller

2230 E Launch Controller is a must when launching “E” engine powered rockets but can be used to launch all Estes engines. Upgrade the capacity of your launch controller with the “E”. This launch controller enables you to launch the E Estes motors, but can launch any Estes Engine. This controller includes a safety switch, continuity check, and that good ole’ button called “Launch”. It comes complete with safety key and 30 ft. of cable. Requires 4 “AA” alkaline batteries, n…

Electron Beam Launch Controller

INSTRUCTIONS Get ready to launch your new rocket with the reliable Electron Beam® Launch Controller. The Launch Controller comes fully assembled with 17 ft (5.2 m) of cable and requires 4 new 1.5V ‘AA’ alkaline batteries – sold separately. A GREAT Controller for launching all mini, standard (A-C) and D powered rockets.

Estes Blast Deflector Plate

New blast deflector plate replaces that old worn out one!

Fin Alignment Guide

FAST & ACCURATE fin alignment Great for three or four finned rockets Fits body tubes ranging from BT-20 to BT-80 A precision molded accessory that makes it easy to glue three or four fins to various sized body tubes ranging from BT-20 to BT-80 diameters. Unique and adjustable vertical fin holders can accommodate either 3/32 in. or 1/8 in. balsa, bass or plywood fins. This is a must-have tool for any serious model rocket builder. Never attach your fins wrong again and remove that pa…

Mini AltiTrak Altitude Trackers (3pk)

Take learning to new heights with this low-cost technology solution for tracking model rocket altitude. These small, easy to transport altitude tracking devices allow for students to track flight data, analyze and graph! Coming in a 3 pack, this makes it easier on your wallet so you can provide engaging learning opportunities for your students. Need a savior from a boring classroom, but want to keep it educational? Introduce the Mini AltiTrak to your rocketry activity to engage students in th…