Adhesives

Adhesives
  • CA Gap Foam Safe 1/2 oz Gold

    CA Gap Foam Safe 1/2 oz Gold

    SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clea…

    $9.99

    Stock Level: 0

    $9.99

  • CA IC-Gel 20g

    CA IC-Gel 20g

    IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE™. IC-GEL™, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL™ can b…

    $7.99

    Stock Level: 3

    $7.99

    Stock Level: 3
  • CA Insta-Set 2 oz

    CA Insta-Set 2 oz

    INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA…

    $6.99

    Stock Level: 0

    $6.99

  • CA Super Thin 1/2 oz Blue

    CA Super Thin 1/2 oz Blue

    Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

    $4.79

    Stock Level: 0

    $4.79

  • CA Un-Cure 1oz Green

    CA Un-Cure 1oz Green

    UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics pa…

    $4.99

    Stock Level: 4

    $4.99

    Stock Level: 4
  • Epoxy 15min-13 oz

    Epoxy 15min-13 oz

    MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.

    $29.99

    Stock Level: 0

    $29.99

  • Epoxy 15min-4.5 oz

    Epoxy 15min-4.5 oz

    MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.

    $13.99

    Stock Level: 0

    $13.99

  • Epoxy 15min-9 oz

    Epoxy 15min-9 oz

    MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.

    $22.99

    Stock Level: 0

    $22.99

  • Epoxy 30min-13oz

    Epoxy 30min-13oz

    SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full …

    $29.99

    Stock Level: 26

    $29.99

    Stock Level: 26
  • Epoxy 30min-4.5oz

    Epoxy 30min-4.5oz

    SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full …

    $13.99

    Stock Level: 16

    $13.99

    Stock Level: 16
  • Epoxy 30min-9oz

    Epoxy 30min-9oz

    SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full …

    $22.99

    Stock Level: 17

    $22.99

    Stock Level: 17
  • Epoxy 5min-13oz

    Epoxy 5min-13oz

    QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CU…

    $29.99

    Stock Level: 10

    $29.99

    Stock Level: 10
More
Loading
(Required)
This field is required.
Top

e-Commerce by Rocket Power